start page | rating of books | rating of authors | reviews | copyrights

UNIX Power Tools

UNIX Power ToolsSearch this book
Previous: 44.17 Handling Arguments with while and shift Chapter 44
Shell Programming for the Uninitiated
Next: 44.19 The Bourne Shell set Command
 

44.18 Standard Command-Line Parsing

Most shell scripts need to handle command-line arguments - options, filenames, and so on. Articles 44.15, 44.16, and 44.17 show how to parse command lines with any Bourne shell. Those methods have two problems. You can't combine arguments with a single dash, e.g., -abc instead of -a -b -c. You also can't specify arguments to options without a space in between, e.g., -barg in addition to -b arg. [6]

[6] Although most UNIX commands allow this, it is actually contrary to the Command Syntax Standard Rules in intro of the User's Manual. The version of getopt on the CD-ROM supports this syntax. The getopts we've seen also support this, but may not in future releases.

Your Bourne shell may have a built-in command named getopts. constraints.[7]getopts lets you deal with multiple complex options without these To find out whether your shell has getopts, see your on-line sh or getopts(1) manual page.

[7] Both bash and ksh have it. getopts replaces the old command getopt; it is better integrated into the shell's syntax and runs more efficiently. C programmers will recognize getopts as very similar to the standard library routine getopt(3).

getopt
If your shell doesn't have getopts, you can use the command named getopt on the CD-ROM. getopts works differently from getopt; we won't cover it here.

getopt takes two or more arguments. The first is a string that can contain letters and colons (:). Each letter names a valid option; if a letter is followed by a colon, the option requires an argument. The second and following arguments are the original command-line options; you'll usually give "$@" (44.15) to pass all the arguments to getopt.

getopt picks each option off the command line, checks to see if the option is valid, and writes the correct option to its standard output. If an option has an argument, getopt writes the argument after its option. When getopt finds the first non-option argument (the first argument that doesn't start with a - character), it outputs two dashes (-) and the rest of the arguments. If getopt finds an invalid option, or an option that should have an argument but doesn't, it prints an error message and returns a non-zero status (44.7).

Your script can use a loop to parse the getopt output. Here's an example script named opttest that shows how getopt works.


|| { 





: 










#!/bin/sh
set -- `getopt "ab:" "$@"` || {
    echo "Usage: `basename $0` [-a] [-b name] [files]" 1>&2
    exit 1
}
echo "Before loop, command line has: $*"
aflag=0  name=NONE
while :
do
    case "$1" in
    -a) aflag=1 ;;
    -b) shift; name="$1" ;;
    --) break ;;
    esac
    shift
done
shift    # REMOVE THE TRAILING --
echo "aflag=$aflag / name=$name / Files are $*"

The script has two legal options. The -a option sets the variable named aflag to 1. The -b option takes a single argument; the argument is stored in the variable named name. Any other arguments are filenames.

The script starts by running getopt inside backquotes (9.16)- and using the set (44.19) command to replace the command-line arguments with the getopt output. The first argument to set, - (two dashes) (44.19), is important: it makes sure that set passes the script's options to getopt instead of treating them as options to the shell itself. An echo command shows the output of getopt. Then the loop parses the getopt output, setting shell variables as it goes. When the loop finds the - argument from getopt, it quits and leaves the remaining filenames (if any) in the command-line arguments. A second echo shows what's in the shell variables and on the command line after the loop. Here are a few examples:

% opttest
Before loop, command line has: -- 
aflag=0 / name=NONE / Files are 
% opttest -b file1 -a file2 file3
Before loop, command line has: -b file1 -a -- file2 file3
aflag=1 / name=file1 / Files are file2 file3
% opttest -q -b file1
getopt: illegal option -- q
Usage: opttest [-a] [-b name] [files]
% opttest -bfile1
Before loop, command line has: -b file1 --
aflag=0 / name=file1 / Files are 
% opttest -ab
getopt: option requires an argument -- b
Usage: opttest [-a] [-b name] [files]

The advantages of getopt are that it minimizes extra code necessary to process options and fully supports the standard UNIX option syntax (as specified in intro of the User's Manual).

- JP, BR


Previous: 44.17 Handling Arguments with while and shift UNIX Power ToolsNext: 44.19 The Bourne Shell set Command
44.17 Handling Arguments with while and shift Book Index44.19 The Bourne Shell set Command

The UNIX CD Bookshelf NavigationThe UNIX CD BookshelfUNIX Power ToolsUNIX in a NutshellLearning the vi Editorsed & awkLearning the Korn ShellLearning the UNIX Operating System